TOOLS
1. The new hub
2. Spanar Box 32mm ,17mm
3. Philips Screw Driver
This is the rear hub for the pcd 100
Before removed the 32mm black nut. you must take out the the hub cover using the phlips screwdriver.
Opened the caliper using 17mm spanar. There 2 nut behind of it.
Pictures shown the caliper had been removed but the hub cover is still there
Used the 32mm box to opened the nut.Its might be hard to opened it.
After hub had been opened,removed the disc and hub and replaced with the new one. Reassmble back all the component and tight it well.
Finish
Wednesday, July 20, 2011
Tuesday, July 19, 2011
Oil Pressure Meter
The green circle is the original oil pressure swtich. This switch is need to be opened and place the brass "T" joint to thats place.
Tool that we need likes used brake hose, teflon tape, brass "T" join,Metal cutter.
more tool that we need to used
Cut the hose using the steel cutter and bend it according tho the above picture.
Put the 3/8 NPT Thread Nut. Its can easily get in any hardware shop.
The location of "T" joint that had been connect to the meter in the car. the original sensor switch also need to be replace. Make sure there was no licking
The meter location in the car
View At Night
Tuesday, July 12, 2011
Roof Lamp
This time i will teach you how to install the roof lamp from other car to other types car
First we must create the tamplete of thats roof lamps. The thamplates must be create according to the back of that roof lamp. So it will fit nicely to the roof.
Draw the line according to the template that we had been creat.
After that cut the roof cover.Usually it was made by thick board.
Put the Roof Lamp to the hole that we had make and tide it with bracket or thin aluminium.
For wiring its only have 2 wire
Red for canstatnt 12V (+Ve)
Black For Ground
Final Result
Credict :Tacra Garage
First we must create the tamplete of thats roof lamps. The thamplates must be create according to the back of that roof lamp. So it will fit nicely to the roof.
Draw the line according to the template that we had been creat.
After that cut the roof cover.Usually it was made by thick board.
Put the Roof Lamp to the hole that we had make and tide it with bracket or thin aluminium.
For wiring its only have 2 wire
Red for canstatnt 12V (+Ve)
Black For Ground
Final Result
Credict :Tacra Garage
Sunday, July 10, 2011
Brake Pad Replacement - MyVi
Bendix general for the perodua myvi
Bendix general type
After the tire had been removed, removed the 14mm nut at the bottom of the calipper.
Remove the 14mm nut from the caliper.
Move up the caliper
Using the screw driver peel out the old pad
Removed the old pad
The old pad.
When the pad is taken out.
Piton Caliper
Put the new pad to the rotor. Make sure the pad with the white steel marked was in inner sider of the rotor.
Because the new pad is thick,the caliper can't to be reassmble back because the piston is out from the caliper. So, we had to push back the piston back to its normal position using tools like at the above. You also can used the screw driver to push the piston back ti its normal position
Reassmble the caliper and tight the 14mm nut.
Final
Saturday, July 2, 2011
Auto Flip Side Mirror Wiring
Switch Wiring
Black + Yellow (Ground Lamp Switch)
Green + White (+12V Lamp Switch)
Brown + Blue (Auto Flip)
Brown + White (Auto Flip)
Blue + Yellow (Power +12V)
Black (Ground)
Yellow + Red
Green + Red
Yellow + Blue
Green + Blue
Yellow + White
Socket Closed Up
Relay Wiring
Red + Black (Power +12V)
Black (Ground -Ve)
Brown + White
Brown + Blue
Brown + Black
Brown
LH Side Mirror
Socket Wiring For Right Side Mirror
Green + Red
Yellow + Red
Yellow + White
Brown + Black
Brown
RH Side Mirror
Socket Wiring For Right Side Mirror
Yellow + Blue
Green + Blue
Yellow + White
Brown + Black
Brown
WIRING PROCESS
Wiring 1 (Switch Socket)
Black + Yellow ---------> Ground or car body (-Ve)
Green + White ---------> T10 Lamp 12V (+Ve)
Brown + White ---------> Brown + White at the Relay
Brown + Blue ---------> Brown + Blue at The Relay
Blue + Yellow ---------> Constant 12V (+Ve)
Black ---------> Ground
Wiring 2 (Relay)
Red + Black ---------> Constant 12V (+Ve)
Black ---------> Ground (-Ve)
Brown ---------> Brown (Left and Right Side Mirror Socket)
Brown + Black ---------> Brown + Black (Left and Right Side Mirror Socket)
Wiring 3 (Left and Right Side Mirror Socket)
Yellow + White ---------> Yellow + White (At the switch)
Wiring 4 (Left Side Mirror Socket)
Yellow + Red ---------> Yellow + Red (At the switch)
Green + Red ---------> Green + Red (At the switch)
Wiring 5 (Right Side Mirror Socket)
Yellow + Blue ---------> Yellow + Blue (At the switch)
Green + Blue ---------> Green + Blue (At the switch)
Credict To : Tacra's Garage
Subscribe to:
Posts (Atom)